LAMBDA
AUDIO
Coming with 1.0
User guide / 06 / 06Sub-bass generatorComing with 1.0

Lambda Audio / VST3 + experimental Audio Unit

Undertone.

Add a sub-bass voice one octave below the low notes of a bass, kick or 808, and keep the original in the mix.

Undertone editor with the sub display, the SUB and OUT meters and the Level, Range, Response and Output controls
Sub displayActual plugin UI
BuildComing with 1.0
FormatVST3 + experimental Audio Unit
AvailabilityShips with 1.0
Reading timeAbout 4 min
On this page

Undertone adds sub-bass under your low notes: the deep rumble you feel more than hear. It plays a new voice one octave below each note, and it can add a second one two octaves below. The added voice follows each note as it moves. Your original sound stays in the mix; Amount sets how much sub is added.

Install and open

You need a Mac with Apple silicon on macOS 13 or newer, or a 64-bit PC on Windows 10 or 11.

  1. Save your project and quit your DAW (your music software).
  2. Run the installer.
  3. Open your DAW. If Undertone doesn't appear, ask the DAW to rescan plug-ins.
  4. Add Lambda Audio → Undertone as an effect on a bass, kick, 808 or group of tracks.

To start your 30-day free trial or enter a licence, click License / trial at the bottom left of the plug-in and sign in to your free Lambda Audio account. When the trial ends, Undertone lets your audio through untouched until you activate it, so your projects still open and play.

On a Mac, Undertone comes as a VST3 and as an Audio Unit. The Audio Unit is still experimental. If anything goes wrong, click Support next to License / trial and send the file it makes to support@lambdaaudio.com.

Quick start

  1. Click the preset name at the top and choose Octave Down.
  2. Play the part and turn Amount to taste.
  3. Click Solo to hear only the sub, then click it again to hear it with your sound.
  4. Set Range just above the highest note that should get a sub.
  5. Watch the OUT meter. If it turns amber or red, turn Output down.

Sub-bass adds a lot of volume, and Undertone has no limiter. Leave some room, or turn Output down.

The controls

Control What it does
Amount How loud the sub is. At 50% it matches the note it comes from.
Deep Adds a second voice two octaves down.
Range The highest note that gets a sub. Notes above it are left alone.
Floor How low the sub goes. Raise it if the low end gets muddy or too heavy.
Focus Holds the sub back where your sound already has plenty of bass. Keeps chords and full mixes from getting muddy.
Sustain Turn left for a sub that dies away faster than the note, right for one that lasts longer. It always stops when the note stops.
Threshold Notes quieter than this get no sub, so quiet noise and room sound are left alone.
Output The final volume.
Solo Plays only the added sub.
Bypass Plays your original sound only.

Deep is heard mostly on higher bass notes. If you can't hear it, raise Range or lower Floor.

Hover over any control to read what it does. Drag a knob to change it, hold Shift for fine moves, and double-click to reset it.

The display

The wide coloured columns are the sub Undertone is adding. The narrow ones are your sound's own low end. The two vertical lines are Range and Floor; the shaded areas outside them are where nothing is added. The dashed line is Threshold.

Two meters sit on the right. SUB shows the added sub and OUT the final level. OUT turns amber, then red, as you get close to clipping.

Presets

Preset Use it for
Octave Down Start here: one octave under anything low.
Subtle Weight Quiet extra weight that you feel more than hear.
Two Octaves Both octaves, for notes up to 240 Hz.
Kick Weight A short, firm sub under a kick that ends with the hit.
Tight Low End A fast sub for busy bass lines; quiet parts stay untouched.
Long Sub A deep sub that lasts as each note fades.
Bass Foundation An octave under bass notes.
Synth Layer A strong layer under synth lines and chords.
Thin Mix Rescue Adds low end to a thin mix.
Deep Rumble A long, heavy rumble, meant as a sound effect.

Click the preset name at the top to open the library. Save current saves your settings as a preset file, and Open file loads one.

If something isn't right

  • You hear no sub: your notes may be above Range, too quiet for Threshold, or your speakers may not reach that low. Click Solo and watch the SUB meter. If it moves, the sub is there. Check on headphones or a system with a subwoofer.
  • Too heavy or too long: lower Amount, raise Floor, or turn Sustain left.
  • Too loud overall: turn Output down.
  • Chords sound muddy: raise Focus and lower Range.

Undertone adds no delay to your audio. Undo is Command+Z on a Mac or Control+Z on Windows while the plug-in window is in front.

Next guide / 01 / 06 Effect chainsMutation